VERIZON WIRELESS NETWORK BOOSTER INSTALL
VERIZON WIRELESS NETWORK BOOSTER FULL
VERIZON WIRELESS NETWORK BOOSTER MAC

If you are using an older router there is a good chance that simply getting a more recent model will make a huge difference. It even looks pretty enough to leave out in the open where you’ll get the best signal.Įvery five years or so a new WiFi standard hits the market, offering better speed and range. Verizon’s new unmistakeable latest-generation Wireless-AC “Quantum Gateway”. Just a few inches can sometimes be enough to avoid interference from a hot water heater or air duct. If you can’t move it, try to at least adjust your positioning or even angle. If your router is connected by coax cable, you can move it anywhere in the house that has a live coax outlet. Moving it to a more central location can make a huge difference.

VERIZON WIRELESS NETWORK BOOSTER INSTALL

Verizon will often install your router in the corner of your house where the phone and power lines come in. Solution 1: Move your router (free + elbow grease) You can push it along by turning your Mac’s WiFi off and back on. Sometimes you have to wait a few minutes for them to update. These connection rates don’t adjust immediately. A strong Wireless-G (802.11g) should get you a Tx Rate of about 50, Wireless-N should get about 300, and Wireless-AC should get you 800+. Right below that you’ll see PHY Mode, which indicates the Wireless generation technology you are connecting with. For example, if you have a 50 megabit plan, I would aim to see a Tx Rate of at least 100 in the places you use the computer the most. Which can be much faster or slower than your actual internet connection. As a rule of thumb, you’ll see the best performance when this is at least twice as high as the speed you are paying for. This is not your internet connection speed but your local connection speed just to your router. This will reveal a lot of additional diagnostic information including your current connection speed (Tx Rate). On a Mac, you can hold the Option key while you click the WiFi icon in the top right corner. If you’re still unable to activate the extender after completing the steps above, or if you had trouble changing the port forwarding settings on your router, you can contact Verizon and escalate to Tier 2 or Tier 3 support.Ĭasatech is also happy to assist with network extender installation and troubleshooting.ĭo you have experience with a Verizon Wireless 4G LTE Network Extender? Let us know how it worked for you in the comments.Before you start, get a reading of your current connection strength so that you know if you’re getting an improvement or not. You should rule out problems with activation and GPS antenna placement before changing these settings. Most routers do not require changing port settings or whitelisting IP addresses. Opening ports can lead to security issues, so don’t try this if you’re inexperienced with networks and network security.Īssign the network extender a static IP address, then open the following ports for that address. Port forwarding and IP whitelisting is for advanced users only. To find it, check the network settings on your computer to find the gateway address. The most common address is 192.168.1.1, but it could be something else. To solve these issues you’ll have to access the Port Forwarding section and IP Whitelisting section in your router’s web GUI. Some routers block communication between the network extender and Verizon’s servers.

What if you’re still stuck?Īpart from activation, the second most common cause for getting stuck at step 8A is your internet router settings. Your device should connect to the extender. You may need to turn off your cellular radio the first time: turn on airplane mode for 10 seconds, then turn it off again.

VERIZON WIRELESS NETWORK BOOSTER FULL

If all goes well, your phone will automatically connect to the network extender when in range, and you’ll see full signal strength and high speeds. You may have to call back to reactivate if you get stuck at step 8a of the setup process (displayed on the network extender screen). In our experience, Verizon doesn’t always get the activation process right. To do this, slide the top cover off, pull to unplug the GPS antenna, and connect the labeled ends of the extension cable to the extender and GPS antenna. If you can’t place the extender near a window, use the GPS extension cable to place the removable GPS antenna closer to a window. Place the extender near a window so the GPS antenna can lock on to multiple satellites. Failure to activate will cause the setup process to stall, and you may need to factory reset the extender.īefore powering on, connect the network extender to your router using an ethernet cable.

VERIZON WIRELESS NETWORK BOOSTER MAC

You will need your MAC address (on the bottom or side of the extender). Verizon fails to mention this, but it’s absolutely required. First, contact Verizon to activate the network extender.

Verizon wireless network booster